These boards will last virtually forever giving your trailer a sleek new look, while … Manufacturers often use roller trailers for the boats they make, which testifies that they can offer adequate support, but for optimum support of any boat, go with carpeted wooden bunks.Check boating catalogs for slick silicone strips that you attach to the top of wooden bunks to greatly diminish the amount of friction between trailer and boat. If you own a boat trail­er and look­ing to pur­chase a new boat, your boat trail­er will not be suit­ed to your new boat.If you fall in to one of the above cat­e­gories, you will need to learn how to adjust your boat trail­er bunks and bunk brack­ets to suit your set­up.By cor­rect­ly adjust­ing your boat trail­er bunks to suit your boat, not only will it sit bet­ter on your trail­er; it will pro­vide a smoother ride while in tran­sit, will help make launch­ing and retriev­ing eas­i­er and if you have keel rollers on your trail­er, the bunks will help to even­ly dis­trib­ute your boats weight on the rollers for a smoother set­up and last­ly, be over­all safer.The first step to ensur­ing your boat is sit­ting cor­rect­ly on your boat trail­er is to check that your boats keel is rest­ing on the Approx­i­mate­ly 70% of the boats weight is in the keel, so it is impor­tant that we focus on this area of your boat and that it is well sup­port­ed.With your boat on your trail­er, climb or posi­tion your­self as best as pos­si­ble under your trail­er to visu­al­ize that your boat is rest­ing on all the keel rollers.

If you own a boat already and look­ing at upgrad­ing or replac­ing your exist­ing boat trail­er. Start at the front of your trail­er and work your way to the rear.As a gen­er­al guide, the rollers at the front of your trail­er will be slight­ly high­er than the rear rollers. The Ultimate Bunk Board is ideal for any boat trailer, PWC or boat lift! On an aluminum boat, determine some of this by examining the bottom of the hull. If you own car­pet bunk guides you will no doubt notice that they con­stant­ly need replac­ing much faster than plas­tic boat trail­er bunks.

Starting at the front of the boat, raise the keel roller until it touches the bottom of the keel. Mounts with 1/2" Trailer Bolt to Bunk Bracket. Learn more today about Venture's complete line of bunk trailers. To properly position the bunks on a trailer so they give adequate support to the boat, it’s first necessary to examine the boat. So check properly.Starting at the top, use an wrench to loosen the bolts holding the keel roller in place, lift the roller so it is touching the boat and retighten the bolt. Tighten the first bolt, move to the next bolt and repeat the process. If this hap­pens, adjust them accord­ing­ly back to their orig­i­nal rest­ing posi­tion. suggestions. We welcome your comments and All the deal­ers are con­cerned about is sell­ing a new boat and trail­er pack­age to the cus­tomer. He holds a Bachelor of Science in wildlife science from Purdue University. Shift the boat back enough to get the winch post relocated back the … The end of the bunks/rollers should be flush with transom and the boweye should reach the winch post. Aluminum Bunk Bracket Replacement Swivel Top for Bolster Brackets. If your boat is still not sit­ting cor­rect­ly, go over your boat trail­er from step 1, and see which part of your boat trail­er is not sit­ting cor­rect­ly with your boat. When you think of the important parts of a boat trailer, it’s easy to pick out the wheels and bearings, the lights and clearance markers, perhaps the brakes or even the coupler where the trailer hooks to the tow vehicle. Your boat will rest on the bunks while you adjust the keel roller, so no further adjustment of the bunks is necessary.Adjust the bunks if your boat is setting on the keel, but is "tipsy" on the trailer. If they are; Great! Made of 1/4" Aluminum. Once you are hap­py that your boats keel is rest­ing on your boat trail­ers keel rollers, it is time to make the adjust­ments to your boat trail­er bunk brack­ets and hard­ware.

I would imag­ine that there are a lot of small com­po­nents that go into the parts of a trail­er.

It’s much the same for multi-roller trailers without keel rollers, except that you’ll be making the appropriate adjustments with the roller packs on the outside of the trailer.

Rarely do deal­ers put in any work to make sure the boat trail­er has been adjust­ed to suit the cus­tomers new boat. Car­pet boat trail­er bunks are gen­er­al­ly designed for use with fiber­glass hulls. But from the point of view of supporting the boat's weight without damage to the hull, either way is ok for most boats. It is also noteworthy, a Venture trailer can be adjusted to fit just about any boat in the size range it is intended for. Using a torque wrench, you need to torque each bolt to the manufactures specification.In a similar way as you did with the rollers, unscrew each bolt with the adjustable screw and reposition the trailer bunks so that they touch the boat, taking particular care not to place your finger between the bunk and the boat.