I used a 3/4" piece of melamine particle board to trace out the correct size circle needed for a lid. To test the cyclone I hooked up a 4" flex pipe and started sucking.The cyclone did a great job with the dust and only the micro particles escaped. Problem was that the bucket filled up too quickly and was too weak to handle the pressure of my 6 HP 16 gallon ShopVac, so it buckled all the time. Cheap & Easy DIY Dust Collector: Watch the video to see how I did it!This is a fantastic, cheap, and extremely easy way to minimize dust in your shop while saving the filter on your existing shop vac! Most of these DIY dust collector projects involve using the Harbor Freight 2HP dust collector. I have had a Thien Cyclone Separator on a 20 gallon trash can for about a year now hooked up to my Ridgid Wet / Dry vac. Over the past two years, I … Suitable for 55 gallon dust bins and compatible with our lightweight drum dolly. wall mounts, extended filtration, hoppers, airlocks, etc. Would the HF be TOO MUCH power to use your type set-up with the 1 1/2" PVC and putting my DUST DEPUTY atop a 55 gallon drum? I have a Torit cyclone dust collector with a 55 gallon drum receptacle and the tall skinny 4-bag filter arrangement shown in the photo below. I used it all day today sucking up a lot of dust but the best thing about it is that since the great majority of the dust stays in the 55 gallon drum, there’s virtually no loss of suction power. ). Fits all DC-3000 series dust collectors and DCF filters. Materials list. Lid for Oneida Air Systems' 35 and 55 gallon steel drums that includes pre-cut holes for mounting the Super Dust Deputy cyclone - Ideal for DIYers creating their own dust collection system.
One adapter kit required per drum. These pieces of wood will hold the body and cyclone up on the wall.Both 2x4s were attached with 3 screws each 180 degrees apart form each other.I had to take off the top hole plug to cut an opening for the intake pipe that extends from the impeller down into the cyclone.I inserted the 5" HVAC pipe into the hole and re-attached the plywood hole plug with 4 screws and caulked around the edges.
Most of these DIY dust collector projects involve using the Harbor Freight 2HP dust collector. At the point the 5" HVAC pipe is lose so it can be moved up after mounting to the wall.I found my studs and attached a large piece of plywood to the wall and a smaller piece just for the motor/impeller.I used long lag bolts to attach the motor to the studs/plywood.For the body of the dust collector support I drilled many pocket holes to be mounted to the plywood on the wall.Mounting both supports to the wall with 1.25" pocket screws.The body was slipped in and more pocket screws attach the wall brackets to the 2x4 installed on the dust collector body.I then pushed the 5" HVAC pipe over the impeller inlet and attached it with 1 screw in the front and sealed it with caulking.I bought a used 55 gallon barrel for $20 and cut the lid off (It was used for vinegar so its not going to kill me with crazy chemicals) to use as the bin for the dust.I used a 3/4" piece of melamine particle board to trace out the correct size circle needed for a lid.I then attached a circle cutting jig to my router and the lid and cut a rabbit all along the edge.I spread caulking along the partcle board to seal it and to give the foam better adhesion.I marked and cut a hole out for the plastic insert to accept the flex hose from the dust collector kit.I screwed the plastic piece on with 3 screws and caulked around the edges.I marked and cut a square hole for a viewing window.I drilled 6 holes along the perimeter of the 1/4" Plexiglas and laid a bead of caulking around it and held it in place with 6 screws.Once the caulking under the lid was dry I attached some adhesive weather stripping to act as a seal to stop any air from getting in/out.The lid is temporarily held on with 4 screws through the top.
That was another problem I had with the 5 gallon bucket….-- Greatness is not found in possessions, power, position, or prestige. Use the trash cans, barrels, and 55-gallon drums to attach as giant collectors, and you will get the amazing guides for using the best filters that will not let I bought a used 55 gallon barrel for $20 and cut the lid off (It was used for vinegar so its not going to kill me with crazy chemicals) to use as the bin for the dust. | Rain Barrel from 330 Gallon Drum If a 55-gallon drum is too small for your needs, perhaps these 330 gallon drums will be more to your liking.
I use metal and cardboard drums, but when they are full the filter bags load up, reduce the overall suction, and are way more trouble to empty than the barrel.