Replace the pump lid by placing the lid in place and pushing down while twisting.

Tighten the lid to avoid air getting into the water line.Restore power to your pool pump. This will force air and water through the hose. If you are seeing air inside of your pool pump or even coming out of the swimming pool return jets there is a good chance that your pump is sucking in air.

When air bubbles stop escaping from the vacuum head, the line is filled with water. Learn which plants thrive in your Hardiness Zone with our new interactive map! Repeat these steps as necessary.Your pool pump is used for a few reasons. Water from an outdoor faucet helps create the siphon.

Below is a video guide to help you.When you want to remove it from the pool pull the vacuum head out of the pool and leave it to suck for a split second, this lets it fill with air briefly that makes it lighter to remove. Here is a brief guide on how to insert a vacuum hose into a pool so that it doesn’t get full of air and send an air block into the pipes.

On mine, I pushed the hose back as far as it could go until my hands hurt and I tightened the clamp with all my might too.

Complete the pool liner installation by installing the skimmer and return holes in the vinyl. Along the way, Gus earned a Bachelor of Arts in communications. If you need any assistance or tuition on how to service your pool in the Henderson area please call PoolStar (702) 557-6625PoolStar™ is a Certified Pool/Spa company that is always dependable, professional, licensed, insured and family-owned. Regular vacuuming of the pool bottom is an integral part of swimming pool maintenance. PoolStar™ is so confident in our service quality, that we will price match any other pool service providers for the first month of service in the greater Las Vegas & Henderson areas! It is typically a small handle-like protrusion on the top of the filter near the pressure gauge. Air may enter the line because of a low water level that admits air through the skimmers, by leaves or other debris clogging the skimmers, or an air leak at the intake port of the pool pump or at pump seals.Turn off power to the pool pump and pool heater.

That PVC fitting is tapered a bit toward the open end, and if you don't get the hose way up toward the coupling, it can work it's way loose from the vibrations. If your pool filter return is not equipped to accept a vacuum hose, then slowly feed the vacuum hose into the water, forcing it six inches or more below the surface. Pools generally don’t require pumps using more than 1 1/2 horsepower; these larger, more powerful pumps tend to circulate the water through the filter too rapidly for proper cleaning. This will force air and water through the hose. The pool pump is a crucial part in the swimming pool’s plumbing as it ensures proper flow of water and circulation. Below is a short video guide to help you. If the water return of your pool filter system is designed to accept a vacuum hose, then slip the hose over the return with the vacuum head held under the water surface. Most vacuum heads will have a two-pronged clip which needs to be squeezed together before inserting in to the pole. This can be done two different ways, depending on your pool's filter system. Replace the pump lid by placing the lid in place and pushing down while twisting. Keep in mind that a filter tank that is half empty (or half full of air) is only able to do half the job filtering your pool.

This keeps air out of the tank and allows for maximum efficiency of filtration.

Twist open the lid of the pump slowly. Run the filter and open the air relief valve on top of the filter. You should see bubbles discharging from the returns as air is forced out of the line into the pool water.Observe the air relief valve on top of the filter canister. Still having issues? Once the shop vac removes the air, turn it off.

Close both the inlet and outlet valve on the pump.

Verify the presence of water in the pump basket. Listen for the hiss of air escaping from the valve. Depending on the model pump, it may have only an outlet valve.Twist open the lid of the pump slowly. How to Get Air Out of Pool Pump. Removing air from a pool line involves priming the system with water to enable the pump to push the air out.

Open the inlet valve on the pool pump, followed by the outlet valve. This process allows air to escape from the pump and relieves pressure.Remove the strainer basket within the pump and clean out any debris, leaves or sticks that are in the strainer. Make sure the head is snapped into place.Attach the vacuum hose to the vacuum head. Lubricate the gasket with petroleum jelly and reinstall the cover. Also turn off the pool cleaning pump if one is installed.

Depending on your pool's system, you may need to attach the adapter to the filter intake first; some systems require connecting the hose to the adapter, then attaching to the system. Also turn off the pool cleaning pump if one is installed.Rotate the air relief valve located on top of the filter canister counterclockwise to open the valve.Close the skimmer valves and leave open the main drain valve.Open the pool pump strainer box cover, usually secured by two knurled knobs. If air is introduced into the vacuum hose, it will make your vacuuming efforts useless.Connect the vacuum head to a telescoping pole.

All Rights Reserved.

If it does, open it to release any pressure that has built up inside the above ground pool pump.Once the air is out, water should start flowing out of it and then you can close it. Gradually open the skimmer valve. Rinse the strainer with a garden hose to ensure all dirt is removed. Now let us talk about how to get air out of pool pump.

Now look for compromises in the pump lid and area right around this.

Empty your pool’s straining baskets daily to reduce the chance of clogged drains, which cause the pump to work harder. Turn off power to the pool pump and pool heater.

When water begins to spurt out of the relief valve, turn the valve clockwise to close it.Turn on the pool heater and the pool cleaning pump.Gus Stephens has written about aviation, automotive and home technology for 15 years. Take nose & rap ashirt around it & stick it into the skimmer pipe. Continue running the filter until water begins to leak out of the air relief valve, or the hiss of air …