Our Magnetic Boat Mount kits are truly universal, and extraordinarily convenient. You said it works well up to 15 mph. Is it near the battery? The website says, “CHIRP DownVision™ will change your underwater view with incredibly clear, photo-like sonar images. J-B Weld 8272 MarineWeld Marine Epoxy – 2 oz. From Fish Finder Mounts .com. So now, the end of the wire, could reach the battery.To connect the black and red wires to the battery, we removed the bolts holding down the circle clamps. RAM Mount Marine Electronics Mount. It works really well at low speed and when I’m stopped. The transducer is turned in the direction that points the butt of the cable towards its destination (steering column) so that there are no bends or extra pressure on the cable. Or did that work at any speed?Hi- this post seems to be getting a lot of attetion and for good reason! We needed extension lines (red and black) to help the power lines reach the battery. We lifted those and inserted the depthfinder power cables under them. Maybe it’s just the way the photo is turned.Anyway, the transducer has a cable that runs to the GPS unit which is fixed on the steering column. So, it looks like a transom mount is out of … Do you think its due to placement of transducer that far forward that once it’s up on plane the water contact is inconsistent?I enjoyed reading this article because I have been thinking about doint this on my 2017 VX ski but have been unsure of the transducer to get. Yes, it is transom and yes we did mount it in Hull.
Raymarine Dragonfly 4 Pro – or a fish finder of your choice. The Dragonfly is IPX6 and IPX7 rated so it can withstand weather, jet stream and short periods of being under water. It does not work well at high speeds. Sea-Doo Sea-Doo 580 & 650 Sea-Doo 720 Sea-Doo 787 Sea-Doo 951 Sea-Doo 4 Stroke Yamaha Yamaha 500 & 650 Yamaha 701 Yamaha 760 Yamaha 800 Yamaha 1100 Yamaha 1200 Yamaha 1200/1300PV Yamaha 4 Stroke Engine Mounts Kawasaki Sea-Doo Yamaha Supercharger Sea-Doo Yamaha Kawasaki Carbs & Injection Electrical Discussion Starter • #1 • Apr 2, 2015. anyone tired to mount a FF and some rod holders. The thin material makes the in hull adhesive mount quite suitable for personal water craft like a WaveRunner, Sea-Doo, or Kayak.Once we agreed on an in hull mount, we decided to glue the transducer directly below the driver’s seat. There was a nice space there with no existing parts mounted that seemed to be perfect for the transducer. LinQ Fishing Cooler – a tough built-in 13.5 gallon cooler specifically created for storing ice, bait and caught fish.
Blue Sea Systems Waterproof In-Line ATO/ATC Fuse Holder. We placed it on the left side because my husband is left handed. Here is a photo of the transducer after it was installed:Marine Epoxy used to adhere the transducer to the inside of the hullOur approach to mounting the cables was to be as minimally invasive as possible. By browsing this site, you are agreeing to our use of cookies in accordance with our
I was going to mount to the transom, but the only place I can put it actually angles away from the jet. So, we used the drill to route a small groove in the speedometer cluster’s plastic cover. Well done. We thought it would be exciting to know depth when we are in open water. Yours appears to be the transom mounted version but you have mounted inhull. The GPS works at high speeds and slow speeds.Cable routing: We are really happy with the placement of the cables. or only for CV or down view? 3 Sea-Doo Features. Save Share. Why was the transducer faced the way it was? Or is it just the sonar (fish and depth) that work up to 15? There seemed to be a big gap in the price range of those products. Ultimate Fish Finder/GPS mount. I do have a question for you though. Were any of the Garmin marine chartplotter/fishfinders ruled out, or did you go right for the DragonFly?Such a great question, Bob. First, to go this route, you really need a brass transducer which does not come stock. The Yamaha steering column was easy to work with as well.Mount positon: it is in the perfect spot and the RAM Mount is performing like a champ! We are pleased that we could use the existing “rubber boot” to get the cables through the hull without drilling. [How-To] Mounting a transducer on a 2006 Sportster 4-TEC - posted in How-To/Product Review: Has anybody done this? Suits Sea-Doo GTi/GTR/GTS 2012-2019. When we finished, the depth finder cables were easily accessible at the steering column.This approach makes the modification unnoticeable and compliments the design of the steering column.The Dragonfly 4 Pro comes with a display mount, but Nick suggested an aftermarket mount called the The Ram Mount required two small holes. Continue with Facebook.
I would still trust a Garmin, Lawrence or similar brand for this purpose and mount. Are you able to confirm the transducer model number please.Hi Stu! Reply. As shown in the photo below, the structure includes a rubber boot (water tight hole through the hull) and the main steering mount plastic. I based in New Zealand Zealand and looking at identical setup but just need to check the transducer you used. Also, the Dragonfly had a couple of more tech savvy features that intrigued me. Super happy with the product.Hey, quick question: does the downfinder feature actually work well, up the the 15 mph you mention?