If your vacuum suction power is low. We have tried to help you in this regard.We are researching for you another troubleshooting guideline like Who am I: I am a Home Improvement Specialist, Cleaning Expert, Product Reviewer.

It can get pretty caked up with dirty after awhile and You can just take a wet paper towel to it and then let it dry.

All pipes are clear, brush and roller free of hair etc, filter not washed but beaten clean, suction THROUGH tubes but as soon as I put the ROLLER/brush section back on the suction stops. Tags: shark ion battery shark vacuum brush not spinning Shark vacuum lights blinking.

just no power. The brushroll seems to be shorting out on the floor head as I vacuum, and it will quickly turn on and off along with the green light, that will also turn on and off with it. However, things happen as we vacuum and sometimes different issues occur. You just need to check out your shark vacuum filters and brush roll. I removed the dust cup and emptied it and now it will not come back on. What can be done? homeplix.com, a blog solely focused on giving away home improvements suggestions.just changed filters on shark navigator nv350nz. I have a shark Lift away. Again, make sure the vacuum is unplugged, and you’re safe.Read the troubleshooting above and save it for future reference in case the problem reappears.I’ve been a dedicated writer for Clean That Floor for approximately 3 years. Might miss there’s two underneath.There are two wheels, you need to do is pop these little cylinders out.When you put them back you kind of use a screwdriver to pop them back into place.Then I’ll show and then there are actually two more screws that you might miss.Well, there’s two that are right inside the main wheels. thanks.My motor has never got hot.We have taken it apart and all parts are clean including hoses.it comes on fine then air makes funny sound and comes out a little rectiangle place on left side of sweeper when looking from the front. Suction loss in Shark vacuums is usually caused by small particles on the metal grate inside the dirt canister or “dust cup” but often, the problem is with the blockage in one of the hoses or blockage in the floor nozzle/brush roll. This means it only needs one square foot of floor space for storage.

could it be that it is not making contact somewhere. Place a washer under that screw head, bend the washer to the curve of the plastic. In the end as not fan is available for purchase we have bought a replacement vacuum.If someone from Shark wants to join this thread and explain something otherwise they would be more than welcome.Sir, I have the same problem as one of your other customers I replaced the heap filter and now it blows off every time you turn on the machine, and no your video on how to clean filters is no help.Sir, the brush roller on my Shark Apex is not spinning. Very recently the motor has gotten very loud and metallic-y sounding. It still performs reasonably well even with this issue.Can I get a replacement seal for this dust cup or can you tell me the name of a material that I can use to replace the faulty one?I had this problem.

I could try welding an aluminium patch onto the fan and redrilling (I build race cars as a hobby) but the light weight of the Aluminium combined with its modest gauge and the fact the whole thing needs to be balanced may make this a job too far.My shark duo clean (purchased just three years ago) turns itself off after 5-10 minutes of vacuuming, although the light stays on there is no sound or suction and when I try to switch it off and turn back on it won’t start right away unless I let it rest for at least 30-45 min. When hose/handle part is disconneCted to use attachments, the power totally goes off. Saw how you change the belt by taking the sides off.You want to change shark duo clean HV 392 main brush roller, My chark navigator works for a few moments and it feels like the engine is empty, then it releases and the engine spins completely in the band, it doesn’t suck. I can push it back on, but it falls back off within 5 minutes. !Dual brush roll system deep-cleans carpets and directly engages floors for a polished look it is very important for vacuum. Looking after and Whatever has stopped your brush roll, it’s probably within your hands reach. Don’t be afraid to flip it and check for what caused it to stop. Allow your shark vacuum to cool for one hour.There is we have discussed some common causes of shark vacuum The vacuum might be overheating because the filters are clogged. Due ti the tube inside the power foot splitting, Shark Australia sent me a replacement foot. At first, you have to need to unplug your vacuum and switch off it. That it is not working.When you look at the very bottom of the unit, you’ll see screws there. See if the filters are clogged and stuff like that.But that has nothing to do with this first position.I’m going to take the canister off. Taking those two sides, lift off the canister.Now you can see this vacuum cleaner looks brand new. If that looks like it’s taken on any dirt dust.So that is the main motor and something is wrong with that. HelpBased on the information you have given, the problem cannot be ascertained. If yes, you can follow the instruction of this Not sure why caps are locked… the base of my shark doesnt lock in place anymore. The motor is like a big problem all the time.The shark vacuum motor could have a problem if it has parts rubbing on parts it will get hot.Your pet hair could be wrapped around the brushes or locking down the beater bar.