JavaScript is disabled.
Sorry to hijack, but How hard is it to replace struts and whats involved? Torque for front brakes 102 Nm or 75 ft/lbs, and rear brakes 47 Nm or 34 ft/lbs. If you have an account, Torque for front brakes 102 Nm or 75 ft/lbs, and rear brakes 47 Nm or 34 ft/lbs. (Notice there's a huge difference between the front/rear, but that's what the manual says.) According to an illustration - the surrounding panel for the display and the two centre face vents are all removed as one piece. Ball joints: main locking nut 103 Nm or 76 ft/lbs. The main mounting with the two big bolts (disc brake cylinder mounting). Tie rod: The nut on the shaft used for adjusting tracking (tie rod end locking nut) 74 Nm or 55 ft/lbs. I have display but no back light. @Alan333- I don't suppose you know how to change the bulb in the display unit above the radio? Thanks a million Alan, your a starall the info I needed and more.
2007-2013 Toyota Corolla How to replace ball joint Πως να αντικαταστήσετε σφαιρικό σύνδεσμο μπαλάκι - Duration: 21:39. parts were $800 for the ready to install set up. Very much appreciated and thanks again. 3L 2004-08 Front 217 294 Toyota For a better experience, please enable JavaScript in your browser before proceeding. not that big of a job. Lower suspension arm to lower ball joint (2 retaining nuts and 1 bolt) - 89 Nm or 66 ft/lbs.
The calipers are in two parts: The main mounting with the two big bolts (disc brake cylinder mounting). The strip is held by push-clips, and comes off by pulling straight forward towards you, start at the far passenger end and work towards the centre. Hub & Wheel Bearing Torque Specification Lookup Year [Select Year] 2015 2014 2013 2012 2011 2010 2009 2008 2007 2006 2005 2004 2003 2002 2001 2000 1999 1998 1997 1996 1995 1994 1993 1992 1991 1990 1989 1988 1987 1986 1985 1984 1983 1982 1981 1980 1979 1978 1977 1976 im replacing both front and rear struts / shocks.
Find out how to access AutoZone's Lower Ball Joints Repair Guide for Toyota Tundra 2001-06. How can you tell if your struts are bad? You must log in or register to reply here. Yiannis Pagonis 16,041 views The actual caliper, held by the slider pins (disc brake cylinder assy). How can you tell if your struts are bad? Torque (both front and rear brakes) 30 Nm or 22 ft/lbs. Lower suspension arm to lower ball joint (2 retaining nuts and 1 bolt) - 89 Nm or 66 ft/lbs. To fix it yourself, you’ll need a torque wrench and sockets to break the main CV joint lock-nut loose, and be prepared to have to take out the lower ball joint as well. Start by removing the long narrow trim strip which encompasses the cupholders and the hazard warning lights button. Inspect front lower ball joint assembly lh As shown in the illustration, move the ball joint stud back and forth 5 times before installing the nut. Ball joints: main locking nut 103 Nm or 76 ft/lbs.
just need the torque specs. Suspension torque specs Discussion in 'Suspension' started by Youth is overrated, Dec 30, 2019.
Tie rod end main nut (tie rod end sub assy) 49 Nm or 36 ft/lbs. not that big of a job. 2010 Toyota Corolla Base 1. Tie rod: The nut on the shaft used for adjusting tracking (tie rod end locking nut) 74 Nm or 55 ft/lbs. Tie rod end main nut (tie rod end sub assy) 49 Nm or 36 ft/lbs. It's held by two bolts, one at each side at the bottom edge. After torque specs for 1990 toyota corolla 1500cc 5afe for bolting head on and cams in please should come with the package containing the head gaskit or upper cylinder kit.Mostly at the back or printed inside the package. By the look of the pic, once that's off you'll probably be able to undo the bolts and remove it, and from there I'd like to think you'll have access to the panel The main mounting with the two big bolts (disc brake cylinder mounting). im replacing both front and rear struts / shocks. Torque (both front and rear brakes) 30 Nm or 22 ft/lbs. Hi lads, can anyone direct me to somewhere I can find the nut torque settings for the tie rods, ball joints and brake calipers please for a 2005 avensis. ...where I can find the nut torque settings for the tie rods, ball joints and brake calipers please for a 2005 avensis.
@Alan333- I don't suppose you know how to change the bulb in the display unit above the radio? (Notice there's a huge difference between the front/rear, but that's what the manual says.) Torque Specs amnt 5th gen T4Rs 3 11-15-2014 12:26 AM Torque Specs JayBluShu 3rd gen T4Rs 9 11-30-2013 09:26 PM OEM Torque Specs SAC-CA-Runner 3rd gen T4Rs 4 03-11-2013 10:07 PM Torque specs rocket67 5th gen AutoZone's Repair Guides tell …
You can post now and register later. parts were $800 for the ready to install set up. Ball joints: main locking nut 103 Nm or 76 ft/lbs. I've come across tutorial for removing radio but not the part above it.
just need the torque specs. Lower suspension arm to lower ball joint (2 retaining nuts and 1 bolt) - 89 Nm or 66 ft/lbs. Using a torque wrench, turn the nut continuously at a rate of 3 to 5 seconds per turn and take the torque …
I have display but no back light. autozone had them, top 3 nuts are 29ft lbs, and the bottom two bolts are 113 ft lbs.Sorry to hijack, but How hard is it to replace struts and whats involved? The actual caliper, held by the slider pins (disc brake cylinder assy). autozone had them, top 3 nuts are 29ft lbs, and the bottom two bolts are 113 ft lbs. I've come across tutorial for removing radio but not the part above it.